RV Fresh Water Tank Filling on City Water? Check These First
If your RV fresh water tank is filling while connected to city water, start by checking the tank-fill valve settings. If those are correct, possible causes include backflow through the water pump or a leak through a tank-fill/selector valve. The next step is identifying the water path, rather than ordering a pump based on the symptom alone.
In episode 216 of The Smart RVer Podcast, I walk through how to approach this problem without turning it into a parts-swapping project.
First, shut off the unwanted water supply
If the tank is filling unexpectedly or overflowing, shut off city water at the campground spigot. Locate the source of the water before continuing.
Do not plug the tank vent or overflow to stop the mess. Do not assume water under the RV is coming from the fresh tank; identify the actual outlet or leaking connection.
Before opening any plumbing, disconnect city water, switch off the pump, and open a faucet to release pressure. Keep hoses, fittings, and exposed potable-water connections clean. Tiffin includes these shutdown and pressure-relief steps in its selector-valve service guidance. [1]
How city water can reach the fresh tank
During normal city-water use, incoming pressure supplies the RV fixtures. The pump supplies fixtures from the fresh tank when you use the onboard water supply.
Some RVs have a separate gravity-fill opening. Others use a utility-center valve to direct the connected hose supply either to the fixtures or into the tank. Use your RV’s diagram to identify the arrangement. Tiffin’s Phaeton manual illustrates a city-water/tank-fill selector; other RVs may have different controls. [2]
The pump also has a water path connected to the tank. A check valve normally prevents reverse flow through that path. Jayco identifies leak-back through pump valves as a possible reason a fresh tank fills on city water. [3]
Step 1: Check the tank-fill and utility-center settings
Start with the controls you can see. Read the panel instructions and compare every relevant valve or dial with the city-water configuration in your owner’s manual.
Look for labels such as City Water, City Fixtures, Normal, or Tank Fill, but do not assume those labels mean the same thing on every RV.
Take a photograph before changing anything. Then correct settings according to the manufacturer’s instructions. Avoid forcing a stiff selector or using a familiar-looking handle position from a different RV.
If the problem began after filling, winterizing, sanitizing, or plumbing service, include that information in your notes. It gives you a useful starting point for checking what changed.
Step 2: Confirm the tank is actually gaining water
A monitor-panel reading is a clue. Make the diagnosis stronger by recording a starting level and comparing it with a later reading while the RV remains in the same position.
Use the companion checklist to record:
- Starting tank level and time.
- Whether the level came from the monitor or a visible tank.
- Utility-center settings before and after correction.
- Where any escaping water appears.
- Whether the rise happens with all faucets closed or during a particular activity.
Keep room in the tank for any supervised test. Do not deliberately overflow it to prove the problem exists.
Step 3: Understand why an off pump can still pass water
The pump switch controls the motor; it does not close a plumbing shutoff valve.
If the pump’s check valve is not sealing, city-water pressure can push water backward through the pump toward the tank. That can happen while the motor is off. Jayco notes that scale on pump valves and the diaphragm can contribute to leak-back. [3]
This makes the pump a possible suspect, but it does not prove the whole pump needs replacement. Record the exact brand and model, then consult its service instructions to determine which checks and service parts apply.
Step 4: Consider the tank-fill valve
On an RV with a pressurized tank-fill route, the selector or fill valve is another component to investigate. A handle pointing to the city-water setting is not, by itself, proof that the internal valve is sealing correctly.
Look for a loose or freely spinning handle, stiffness, or visible leakage around the assembly. Tiffin lists these among selector-valve problems that can require service. [1]
If filling continues after you have confirmed the settings, use the RV’s plumbing diagram and component service procedure to distinguish the fill-valve route from the pump route. Have a technician isolate the paths if access or routing is unclear. Avoid disconnecting lines under pressure as a trial-and-error test.
Step 5: Check shower recirculation equipment, if installed
Some RVs have a shower water-saving system that sends water back to the fresh tank while you wait for hot water. Tiffin describes this function in its ShowerMiser-equipped Phaeton. [2]
If the tank rises specifically when someone uses the shower controls, check the recirculation setting against that system’s instructions. This is an additional route worth checking on equipped RVs; it does not explain every case of unexplained filling.
What your observations tell you
| Observation | What to investigate next |
|---|---|
| Filling stops after correcting utility-center settings | Record the correct configuration and verify it stays stable. |
| Filling continues with settings correct, and faucets closed | Investigate pump backflow and any separate tank-fill route. |
| Tank level rises during shower use | Check a shower return-to-tank system, if equipped. |
| Water appears beneath the RV without a confirmed tank-level rise | Identify the leaking fitting, drain, or outlet before diagnosing backfilling. |
These observations help choose the next check. They do not identify a failed part on their own.
Can you keep using the RV?
If city water keeps filling the tank, disconnect it while arranging a repair. You may be able to use the fresh tank and pump temporarily if they operate normally and don’t leak. Shut the pump off when leaving the RV unattended, and stop using the system if you find damage or cannot control the water flow.
Before reconnecting city water, follow your RV’s pressure requirements and regulator guidance. A regulator protects against excessive supply pressure; it does not prove a leaking valve has been repaired.
Verify the repair before calling it finished
After correcting settings or completing the specified repair, repeat a supervised check with room left in the tank. Record the starting level and time, close the faucets, and monitor for an unexpected rise.
Inspect serviced connections for drips. If the original problem developed slowly, a short test without visible change is only an initial check. Continue monitoring during subsequent use before leaving the connection unattended.
The goal is simple: identify how the water reaches the tank, repair that path, and verify the result.
Download the troubleshooting checklist
Keep your findings together with the Fresh Tank Filling on City Water? Troubleshooting Checklist. It includes spaces for the pump model, utility-center settings, starting tank level, test results, and observations.
Use it while working through these checks or bring it to your repair appointment. Clear notes help explain what happened and what you have already checked.
Listen to The Smart RVer Podcast
Join me, Eric Stark, for episode 216 of The Smart RVer Podcast as we work through unexpected fresh-tank filling and the checks to make before spending money on parts. RV fresh water tank filling on city water
For more practical DIY RV maintenance and repair guidance, explore our fresh-water troubleshooting resources and keep learning how your RV works—so you can spend more time enjoying the trip.
Manufacturer references
These references explain example systems. Your RV and component manuals determine the correct settings and service procedures for your equipment.
Why is my fresh water tank filling when I’m hooked to city water?
Check the tank-fill settings first. If they are correct, investigate the available plumbing paths, including the pump check valve and the tank-fill valve. Shower recirculation is another possibility on equipped RVs.
Can this happen with the water pump switched off?
Yes. An off motor does not physically isolate the pump’s water connections. A leaking check valve can allow reverse flow. [3]
Should I replace the water pump immediately?
Confirm the water path first. A utility-center setting or another valve may explain the symptom. Use the pump’s model-specific instructions before choosing a repair.
Is every RV fresh tank supposed to fill from the city-water connection?
No. The filling method depends on the RV’s plumbing design. Check your manual rather than assuming the hose connection fills the tank.
Should I leave the fresh tank drain open to manage the problem?
Use the drain for its intended purpose, following the RV instructions. Leaving it open does not repair the unwanted filling. Shut off the incoming supply while investigating.


